From Pattern to 3D Sample: Your First Garment in CLO

Your first garment in CLO comes down to four jobs: draft a pattern, sew it, place it around an avatar, and simulate. CLO has a tool for each job, so you can reach a draped 3D sample without drawing every line by hand.

Here is what each tool does, where to find it, and which Help Center article has the full details.

How Do You Draft Your First Pattern With Pattern Drafter?

Pattern Drafter creates a pattern from measurement points. If you want the pattern to fit an avatar, open the avatar first.

  1. Click 2D > Pattern Drafter in the top menu.
  2. Choose a Pattern Type.
  3. Choose how many measurements you see:
    1. General: the full list of common Points of Measure for that style.
    2. Simple: the most common points, for quick edits.
    3. Custom: applies automatically when you pick your own list.
    4. Click Match to Avatar Size to adjust the measurements to your avatar, or enter your own values. If the button is disabled, restart Pattern Drafter and try again. Matching works with CLO avatars only.
    5. Create the pattern in the Pattern Drafter window.

CLO builds a parametric pattern and adds the measurements you defined as 2D POMs in the POM Object Browser.

How Do You Edit a Pattern Later?

You can edit a Pattern Drafter pattern in two ways and keep its parameters:

  • In Pattern Drafter: open it, choose to edit the existing parametric pattern, and change the values.
    With the Edit POM tool: click the tool in the 2D toolbar, click a POM, and enter a new length.
  • Edit through one of these two ways. Editing the parametric pattern directly breaks its connection with Pattern Drafter.

Can You Draft From a Sketch?

AI Pattern Drafter (Beta) uses a sketch to generate measurements and draft a pattern for you. Click AI Pattern Drafter (Beta) at the top right of Pattern Drafter. Matching to an avatar works with CLO avatars only.

Full steps: Pattern Drafter

How Do You Sew Your Pattern Automatically?

Auto Sewing sews your patterns based on where you placed them on the avatar. CLO uses the avatar’s Arrangement Points to decide how pieces connect, so place each piece on the right point first. Darts and pleats can sew automatically without arranging.

Auto Sewing supports specific garment types, parts, and layers. Check the Help Center article before you start so you pick a style that works.

Full steps and limits: Auto Sewing

How Do You Place Patterns Around the Avatar Automatically?

Auto 3D Arrangement places the patterns around the avatar for you. It learned from many pattern files and decides where each piece goes from its shape. It also reads symmetry and sewing information, so apply symmetry and sewing before you run it.

  1. Click 3D Garment > Auto 3D Arrangement in the main menu, or Auto 3D Arrangement in the 3D toolbar.
  2. Click Proceed. CLO arranges patterns in order, and each step is classified by color and transparency.
  3. Click Back and Next to check each step.
  4. Click OK to finish.

Patterns that are too small, or analyzed to the same location, may be arranged with lower accuracy. Check those pieces by hand.

Full steps: Auto 3D Arrangement

How Do You Simulate Your First Garment?

Click Simulate. Gravity pulls all the pattern pieces toward the floor, and they drape onto the avatar and other static objects in the way. When seamlines are set, the fabric drapes while the seams are sewn.

You can find it in two places:

  • Main menu: 3D > Simulate
  • 3D toolbar: click and hold the simulate tool to switch between options in the pop-up

Which Simulation Mode Should You Choose?

Mode What you get

  • Normal (Default) More efficient, with faster speed
  • Fitting (Accurate Fabric) More defined simulation, with fabric stretch shown more realistically
  • Animation (Stable) More defined simulation, but speed may decrease

CPU or GPU?

CPU and GPU change how collision is calculated: through your processor or your graphics card. GPU simulation has the same accuracy and collision handling as CPU in all modes. For trims, collision and weight only work with CPU simulation.

Full details: Simulation

Where Should You Start?

Open an avatar, draft a simple pattern in Pattern Drafter, then work through the sewing, arrangement, and simulation articles above. Run Simulate in Normal mode first, then switch to Fitting mode to see how fabric stretch changes. You can try the whole workflow with a free trial of CLO.

Leave a Reply